Revel Embrace Manuel d'utilisateur

Embrace Loudspeaker

Figure 8. In this 7.1-channelsystem, a pair of EMBRACEsurrounds are shown placed onthe side walls. Direct-radiatorspeakers (e.g.,GEM speakers)are plac

Figure 9. In a Dual Drive™7.1-channel system, a pair ofEMBRACE surrounds are shownplaced to cover the entire listen-ing area (from the front to rearro

Figure 10. Installing closed-endouter brackets on a wall.MOUNTINGEMBRACE surrounds are available in two versions. The wall-mountversion includes a pai

Figure 11. Routing andconnecting the speaker wire. Figure 12. Mounting anEMBRACE on a wall. 6. At each site, route the speaker wire through the cutout

Figure 13. Installing closed-endouter brackets and shoulderscrews on a ceiling. MOUNTING (CONTINUED)MOUNTING AN EMBRACE ON A CEILINGNOTE: Ceiling inst

Figure 14. Routing and connecting the speaker wire. Figure 15. Mounting anEMBRACE on a ceiling. 6. At each site, route the speaker wire through the cu

Figure 16. How to connect theEMBRACE for dipole or bipoleoperation, the most common typeof installation. NOTE: Do not remove the gold-plated shorting

Figure 17. How to connect aremote control system to therelay input terminals on theEMBRACE rear panel.REMOTE DIPOLE/BIPOLE SWITCHINGEMBRACE surround s

Figure 18. How to connect theEMBRACE surround in aDual Drive™ system. SPEAKER CONNECTIONS (CONTINUED)DUAL DRIVE™ SYSTEM CONNECTIONSA multi-channel Dua

Figure 19. The EMBRACElevel, proximity, and mode con-trol locations and initial settingsfor dipole/bipole operation.SYSTEM OPTIMIZATIONThe EMBRACE may

TABLE OF CONTENTSINTRODUCTION...3ABOUT THE MANUAL AND WARRANTY...3DESCRIPTIO

SYSTEM OPTIMIZATIONDIPOLE OR BIPOLE MODE OPERATION (CONT’D)3. If EMBRACE surrounds will be placed 3 feet (1 meter) or lessaway from the rear wall, set

Figure 20. The EMBRACElevel, proximity, and mode con-trol locations and initial settingsfor Dual Drive™ operation.main listening position. Be sure to

CABINET CAREEach EMBRACE speaker cabinet has a paint finish and does notrequire any routine maintenance. Use a soft cloth, dampened withwater only, to

Figure 21. Overall dimensionsfor the EMBRACE surround loudspeaker.EMBRACE Owner’s Manual23SERVICE INFORMATIONIn the unlikely event that your Revel com

19748 DEARBORN STREETCHATSWORTH, CA 91311PH: (818) 717-0770 • FAX: (818) 701-3755www.revelspeakers.comP/N 9301138-002

Figure 1. The EMBRACE surround loudspeaker.INTRODUCTIONEMBRACE sets an entirely new standard for surround channel per-formance where stunning musical

Figure 2. The EMBRACE transducer, control, and connection locations.DESCRIPTIONEach Revel EMBRACE surround speaker uses an 8-inch mica andcarbon-fille

short winding lengths. A copper shorting ring is employed todecrease inductance and flux modulation. The result is a dramaticreduction in distortion.

Figure 3. In this 5.1-channel system, a pair of EMBRACEsurrounds are shown placed tothe sides of the listening areawith optimum coverage for thefront

Figure 4. In this 5.1-channelsystem, two pairs of EMBRACEsurrounds are shown placed tothe sides of the listening area. Figure 5. As an alternative 5.1

Figure 6. In this 7.1-channel system, two pairs of EMBRACEsurrounds are shown placed onside walls. Ceiling placement isalso possible using an optional

Figure 7. As an alternative 7.1-channel system, one pair ofEMBRACE surrounds is shownplaced on the rear wall withanother pair on the side wall. Asan o