Revel C32 Manuel d'utilisateur

Revel Performa C32 LoudspeakerOwner’s Manual3 Oak Park, Bedford, MA, 01730-1413 USA | Telephone: 781-280-0300 | Fax: 781-280-0490 | www.revel

10Input Panel (continued)The numbers in Figure 4 on the previouspage correspond with the numbered itemsin this section.2. High Frequency Level (dB)Con

11ON TOP OF MONITORSet the Placement Compensation switch toOn Top of Monitor if the C32 loudspeakeris placed on top of a video monitor asshown in Figu

12Adjustable Spike FootingWhen the C32 is shipped, spike footing isattached to the left pad identified in Figure2 on the bottom of page 6. For optimal

133. Locate the two threaded inserts on thebottom of the cabinet. These inserts areidentified on the left side of Figure 9 atthe bottom of the previou

14Making Connections (continued)• Vertical bi-amplified connections mustbe made with identical poweramplifiers. Horizontal bi-amplifiedconnections can

153. Connect another pair of loudspeakerwires to the C32 input connectorslabeled Low Frequency. Then, connectthe same pair of loudspeaker wires tothe

16Vertical Bi-Amplified Connections(continued)To make vertical bi-amplified connections:1. Remove the input panel shorting-strapsidentified in Figure

17OPTIMIZINGPERFORMANCETo optimize the C32 for best performance:1. When the C32 is connected, set theHigh Frequency Level identified inFigure 3 (page

18Optimizing Performance (continued)• The C32 must be used with at leastan 80Hz crossover.• Selecting the appropriate crossoverbased on accurate in-ro

DefinitionSpecification Value19SPECIFICATIONSSensitivityImpedance86.5dB SPL with 2.83Vrms @ 1m (4 pi anechoic)5.8Ω (nominal)3.3Ω (minimum @ 80Hz)Indic

2TABLE OF CONTENTSDocumentation Conventions . . . . . . . . . . . . . . . . . . . . . .3About the C32 . . . . . . . . . . . . . . . . . . . . . . .

The following information must beincluded when a loudspeaker is returnedfor service:• name• company name• street address, city, state, and zip code• t

21NOTES

22AAbout the, C32, 4Adaptor, “Y” 14, 15, 16Adjustable Spike Footing, 12 (ill.)Aluminum Flux-Stabilizationring, 4, 8BBaffle Edges, 4, 8Bi-Amplified Co

PPacking Materials, 6 (ill.)Placement Compensation, 4, 5,8, 10, 18Polarity, 13Power Amplifier Connections,14, 15, 16, 18, 19Pre-amplifier Connections,

243 Oak Park, Bedford, MA, 01730-1413 USA | Telephone: 781-280-0300 | Fax: 781-280-0490 | www.revelspeakers.comCustomer Support: Telephone: 781

3DOCUMENTATION CONVENTIONSThis document contains general safety, installation, and operationinstructions for the Revel Performa C32 Center-Channel Lou

4ABOUT THE C32Thank you for purchasing the Revel PerformaC32 Center-Channel Loudspeaker. Withstunning acoustical precision, the C32delivers exceptiona

5Since 1996, Revel has stood at the forefrontof loudspeaker design. Backed withHarman International’s extensive researchand design facilities, the Rev

6Unpacking (continued)To unpack the C32:1. Place the packing carton upright on asoft towel or carpeted floor and fullyopen the top flaps as shown in s

7NoteWhile the loudspeaker is upside-down, itis recommended to position the spikefooting as desired. Refer to the AdjustableSpike Footing section that

8Driver Complement (continued)3. Woofers• Two 5-inch (127mm) conesconstructed with Organic CeramicComposite cone material• Die-cast basket to eliminat

9INPUT PANELThe numbers in Figure 4 (above) correspondwith the numbered items in this section.1. Placement CompensationControlOptimizes the C32’s resp